ASME B89.4.21.1 pdf download
ASME B89.4.21.1 pdf download Environmental Effects on Coordinate Measuring Machine Measurements 1 scOPE This Technical Report discusses important influences of the environment on dimensional and geometric measure-ments performed using coordinate measuring machines (CMMs) including influences on both the machine and theworkpieces to be measured.This Report discusses the thermal effects related to the use of tactile CMMs, but manyof these effects...
ASME B89.4.23 pdf download
ASME B89.4.23 pdf download X-Ray Computed Tomography (CT) Performance Evaluation 1 scOPE This Standard specifies the dimensional measurement accuracy of industrial X-ray computed tomography (CT)systems for length, size, and form measurands of sphere-based test objects made of homogeneous materials.Medical cT systems are outside the scope of this Standard.The material properties of the measured test objectsare restricted to three classes of...
ASME B73.3 pdf download
ASME B73.3 pdf download Specification for Sealless Horizontal End Suction Metallic Centrifugal Pumps for Chemical Process 1 SCOPE This Standard covers sealless centrifugal pumps of horizontal end suction single stage and centerline dis- charge design. This Standard includes dimensional interchangeability requirements and certain design fea- tures to facilitate installation and maintenance. It is the intent of this Standard that pumps...
ASME B89.1.2M pdf download
ASME B89.1.2M pdf download Calibration of GageBlocks by ContactComparison Methods(Through 20 in. and 500 mm) scOPE This Standard covers procedures to establish unifiedpractice in calibration laboratories for measuring gageblocks up to 20 in. (500 mm) in length (size) by contactcomparison methods. it does not cover interferometriccomparison methods. 2OBJECTIVE To establish an American standard for laboratory cal-ibration of gage blocks by...
ASME B89.1.10M pdf download
ASME B89.1.10M pdf download DIAL INDICATORS FOR LINEAR MEASUREMENTS 8.2.4 Physical Dimensions. Refer to Fig. 1 for standard dimensions of Type A dial indicators. Types B and C (Figs. 2 and 3) are illustrated for general appearance. The individual manufacturer’s standard practice should be consulted. Table 1 shows size group limits for nominal bezel diameters and corresponding minimum position distances...
ASME B89.4.10 pdf download
ASME B89.4.10 pdf download MethodsforPerformance Evaluation of Coordinate Measuring System Software coordinate measuring system (CMS): any piece ofequipment that collects coordinates (points), calculates, and displays additional information using the measured points. datum: a theoretically exact point, line, or plane derived from a feature on a part. See ASME Y14.5M-2018. least-squares fit feature: a feature ofperfect form, corresponding to a set...
ASME B89.4.19-2021 download
ASME B89.4.19-2021 download Performance Evaluation of Laser-Based Spherical Coordinate Measurement Systems 1 ð21Þ SCOPE This Standard prescribes methods for the performance evaluation oflaser-based spherical coordinate measurement systems and provides a basis for performance comparisons among such systems. Definitions, environmental require- ments, and testmethods are included with emphasis on point-to-pointlength measurements. The specified testmethods are appropriate for the performance evaluation ofa...
ASME B107.17 pdf download
ASME B107.17 pdf download Gages and Mandrels for Wrench Openings 1 sCOPE This Standard establishes final inspection gage sizesand test mandrel sizes for wrench openings and sparkplug wrench openings for inch and metric sizes. ThisStandard does not cover every available size,but onlythose most commonly manufactured. APPLICATION The gages covered by this Standard shall be used toensure the manufacture of conforming...
ASME B107.18 pdf download
ASME B107.18 pdf download ASME STANDARDS COMMITTEE B107 Hand Tools and Accessories Wre twister pliers shall incorporate a device, which,when actuated, wili cause the plers to rotate abaut itslongitudinal axis. The halves of the plers shall be pernma-nently joined with a through fastener that shali act asthe pivot or fulcrum point of the pliers. A locking device,when engaged, shali hold...
ASME B107.36 pdf download
ASME B107.36 pdf download PLIERS: LOCKING CLAMP, AND TUBINI! PINCH-OFF 4.4 Handles Handles of pliers shall be through hardened from 30 to 50 HRC or case hardened from 75 to 86 HRlSN, with a case depth of a minimum of 0.010 in. (0.25 mm). Handles shall be so shaped as to afford a comfort- able grip and shall be free...