ASME MFC-11M pdf download
ASME MFC-11M pdf download MEASUREMENT OF FLUID FLOW BY MEANS OF CORIOLIS MASS FLOWMETERS 3.3 Physical Installation 3.3.1 General. The manufacturer should describe thepreferred installation arrangement and state any restric-tions of use.See Appendix C. If needed, strainers, filters,air, and / or vapor eliminators or other protective devicesshould be placed upstream of the meter for the removalof solids or vapors that...
ASME MFC-22 pdf download
ASME MFC-22 pdf download Measurement of Liquid by Turbine Flowmeters 6.2.2 If a bypass is permitted around a meter or a battery of meters, it should be provided with a blind or a positive shutoff, double block-and-bleed valve with telltale bleed. The bypass should be sealed with a tam- perproof seal if the meter or battery of meters is used...
ASME N509 pdf download
ASME N509 pdf download NUCLEAR POWERPLANT AIR-CLEANING UNITS AND COMPONENTS 4.3 Size (Installed Capacity) of Air-Cleaning Unit The installed capacity cfm (m 3 /hr) of the air cleaning unit shall be no greater than the limiting installed capacity of any bank of components contained in the aircleaning unit through which the airflow must pass. The 2 installed capacity of any...
ASME N511 pdf download
ASME N511 pdf download In-Service Testing of Nuclear Air Treatment, Heating, Ventilating, and Air-Conditioning Systems 3.3.1 Inspection and Test Parameters. Parameters that need to be observed, calculated, and recorded in order to meet the requirements of this Standard shall be identified for each system. 3.3.2 System Operating Conditions. Operating con- ditions required for in-service testing shall be deter- mined for...
ASME NM.2 pdf download
ASME NM.2 pdf download Glass-Fiber-Reinforced Thermosetting-Resin Piping Systems ASME Standards for Nonmetallic Pressure Piping Systems (a) the length of twist produced by stranding filaments,such as fibers, wires, or roving; length oftwist of a filamentis usually measured as the distance parallel to the axis ofthe strand between successive turns of the filament.(b) the angle that such filaments make with the axis...
ASME NQA.TR pdf download
ASME NQA.TR pdf download Evolution of Quality Assurance Principles and Requirements in the U.S. Nuclear Industry Whereas previous DOE quality assurance directives were applied onlyto contractors, DOE O 5700.6C required both the DOE and contractor organizational elements to develop and implement quality assurance programs that complied with the ten criteria. Attachment 1 to DOE O 5700.6C provided guidance for developing...
ASME NTB-3 pdf download
ASME NTB-3 pdf download Gap Analysis for Addressing Adequacy or Optimization of ASME Section III, Division 5 Rules for Metallic Components 1.2 Issue I. 2 – Simplified Bounds for Creep Ratcheting 1.2.1 Summary From O’Donnell, Hull and Malik [1] Item OG- 5: The Draft Code Case for Alloy 617 imposes ratcheting strain limits that are similar to the limits given...
ASME NTB-4 pdf download
ASME NTB-4 pdf download Background Information for Addressing Adequacy or Optimization of ASME BPVC Section III, Division 5 Rules for Nonmetallic Core Components 2 CODE APPROACH This section provides the basis for the code and a typical design sequence for a graphite core component. Because there is not a standardized graphite grade for nuclear applications, the code places the responsibility...
ASME NTB-5 pdf download
ASME NTB-5 pdf download Guidance for Determination of Risk-Informed Safety Classification for Light Water Reactor Nuclear Facility Pressure Retaining Components 3RISK-INFORMED SAFETY CLASSIFICATIONS (a) The RISC process is described in Appendix I of this document.Pressure-retaining items should be classified high-safety significant (HSS) or low-safety significant(LSS), except as noted in 3(b) below.(b)(1) Class 1 portions of the reactor coolant pressure boundary...
ASME PTB-13 pdf download
ASME PTB-13 pdf download Cri teria for Pressu re Retai n in g M etal l i c Com pon en ts U si n g Ad d iti ve M an u factu ri n g 3MATERIALS (a) For the purpose of these criteria, Material is defined as an additively manufactured component meeting the requirements of the ASME material...