API 19V pdf download
API 19V pdf download Subsurface Completion Isolation (Barrier) Valves and Related Equipment
This specification provides the requirements for subsurface completion isolation (barrier) valves (SCIV) andrelated equipment as they are defined herein for use in the petroleum and natural gas industries. Included arethe requirements for design, design validation grades, quality levels, manufacturing, functional evaluation, repair,redress, handling, and storage.SCIVs provide a means of isolating the formation or creating a blockage in thetubular to facilitate the performance of pre- and/or post-production/injection operational activities in the well
Additional requirements for HPHT products are included in Annex l.
When closed, the SClV provides an obstacle or impediment to flow and/or pressure from above and/or belowand a means of isolating the formation within a conduit. The SClV is not designed as an emergency or fail-safeflow-controlling safety device.
This specification does not cover installation and maintenance, control systems such as computer systems, andcontrol conduits not integral to the SCIN.Also not included are products covered under lSO 17078,ISO 16070,ISO 14310,ISO 10432,ISO 10423， and the following products: downhole chokes， wellhead plugs，slidingsleeves, casing-mounted flow-control valves, injection valves, well-condition-activated valves, or drill-stem testtools.This specification does not cover the end connections to the well conduit.
2 Normative References
The following referenced documents are indispensable for the application of this document.For dated referenc-es, only the edition cited applies.For undated references, the latest edition of the referenced document (includingany amendments) applies.
APl’Technical Report 5C3, Calculating Performance Properties of Pipe Used as Casing or Tubing,Annex A
API Specification 20A, Carbon Steel, Alloy Steel, Stainless Steel, and Nickel Base Alloy Castings for Use in thePetroleum and Natural Gas Industry
APl Manual of Petroleum Measurement Standards Chapter 10.4,Determination of Sediment and Water inCrude Oil by the Centrifuge Method (Field Procedure)
APl Specification Q1, Specification for Quality Management System Requirements for Manufacturing Organiza-tions for the Petroleum and Natural Gas lndustry
ANSI/NACE MR0175-2015IISO 15156,Petroleum and natural gas industries- Materials for use in H,S-contain-ing environments in oil and gas production
ASME3 Boiler and Pressure Vessel Code (BPVC),Section ll,Materials Specification—Part D: Properties
ASME Boiler and Pressure Vessel Code (BPVC),Section VIl, Rules for Construction of Pressure Vessels—Di-vision 1,UW-40: Procedures for Post-weld Heat Treatment
ASME Boiler and Pressure Vessel Code(BPvC), Section VIIl, Rules for Construction of Pressure Vessels—Di-vision 2, Part 5: Design by Analysis
ASME Boiler and Pressure Vessel Code (BPVC), Section VII, Rules for Construction of Pressure Vessels—Di-vision 3: Alternative Rules for Construction of High Pressure Vessels
ASME Boiler and Pressure Vessel Code (BPVC),Section vIl, Division l, UW-51, Radiographic Examination ofwelded Joints
ASME Boiler and Pressure Vessel Code(BPVC),Section V1Il, Division 1, Appendix 8, Methods for Liquid Pen-etrant Examination (PT)
ASME Boiler and Pressure Vessel Code (BPVC), Section lX, Welding and Brazing QualificationsASQ3 H1331,Zero Acceptance Number Sampling Plans
ASTM’ D395-16e1, Standard Test Methods for Rubber Property—-Compression Set
ASTM D412-16, Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—TensionASTMD429-14,Standard Test Methods for Rubber Property—Adhesion to Rigid Substrates
ASTM D638-14,Standard Test Method for Tensile Properties of Plastics
ASTM D790-17,Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics andElectrical Insulating Materials
ASTM D1414,Standard Test Methods for Rubber O-Rings
ASTM D1415-O6 (2012), Standard Test Method for Rubber Property—International Hardness
ASTMD1708-13, Standard Test Method for Tensile Properties of Plastics by Use of Microtensile SpecimensASTM D2240-15,Standard Test Method for Rubber Property—-Durometer Hardness
ASTM D2990-17,Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture ofPlastics
ASTME21-09, Standard Test Methods for Elevated Temperature Tension Tests of Metallic MaterialsASTM E23-16b, Standard Test Methods for Notched Bar lmpact Testing of Metallic Materials
ASTM E94/E94M-17,Standard Guide for Radiographic Examination Using Industrial Radiographic FilmASTME111-04(2010),Standard Test Method for Young’s Modulus,Tangent Modulus, and Chord ModulusASTME165,Standard Test Method for Liquid Penetrant Examination
ASTM E709,Standard Guide for Magnetic Particle Testing
ISO 3601-1, Fluid power systems – O-rings – Part 1: Inside diameters, cross-sections, tolerances anddesigna-tion codes
ISO 3601-3, Fluid power systems – O-rings – Part 3: Quality acceptance criteriaISO 6506 (all parts)，Metallic materials — Brinell hardness test
