ISO 19574 pdf download

ISO 19574 pdf download

ISO 19574 pdf download Footwear and footwear components — Qualitative test method to assess antifungal activity (growth test) 4Principle The test and control specimens of footwear are inoculated with a mixed spore suspension of selectedmould test strains or with a single test strain according to the specific claim. Antifungal performance is qualitatively determined by visual assessment of fungal growth afterspecified...

ISO 19587 pdf download

ISO 19587 pdf download

ISO 19587 pdf download Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at elevated temperature in air atmospheric pressure — Determination of in-plane shear strength 1 Scope This document specifies a method for the determination of in-plane shear strength of continuousfibre-reinforced ceramic composites at elevated temperature in air or inert atmosphere by theasymmetric four-point bending...

ISO 19670 pdf download

ISO 19670 pdf download

ISO 19670 pdf download Fertilizers and soil conditioners — Solid urea aldehyde slow release fertilizer — General requirements This document specifies general requirements, analytical methods, sampling and preparation of testsample, marking and labelling, packaging, transport and storage for solid urea aldehyde slow releasefertilizer. This document applies to pure solid urea aldehyde slow release fertilizer, i.e.urea formaldehyde (UF),methylene urea (MU), crotonylidene...

ISO 19809 pdf download

ISO 19809 pdf download

ISO 19809 pdf download Packaging — Accessible design — Information and marking 1 Scope This document provides requirements and recommendations concerning accessible design of consumerpackaging with regard to information and marking. This document specifies considerations and methods for designing and presenting information andmarking to make consumer packages accessible to people with the widest range of capabilities byconsidering their sensory and...

ISO 19880-5 pdf download

ISO 19880-5 pdf download

ISO 19880-5 pdf download Gaseous hydrogen — Fuelling stations — Part 5: Dispenser hoses and hose assemblies 3.8 pressure rating maximum pressure at which it is permissible to operate a component as specified by the manufacturerat the maximum temperature expected during service 3.9 proof pressure pressure applied during a non-destructive test and held for a specified period of time to...

ISO 19905-3 pdf download

ISO 19905-3 pdf download

ISO 19905-3 pdf download Petroleum and natural gas industries — Site-specific assessment of mobile offshore units — Floating units This document specifies requirements and recommendations for the site-specific assessment of mobilefloating units for use in the petroleum and natural gas industries. It addresses the installed phase, at aspecific site, of manned non-evacuated, manned evacuated and unmanned mobile floating units. This...

ISO 19967-1 pdf download

ISO 19967-1 pdf download

ISO 19967-1 pdf download Heat pump water heaters — Testing and rating for performance — Part 1: Heat pump water heater for hot water supply Unless otherwise stated by the manufacturer, the air inlet and air outlet orifices shall not be less than1 m from the surfaces of the test room; this also applies to any measuring ducts. Any direct...

ISO 19349 pdf download

ISO 19349 pdf download

ISO 19349 pdf download Plain bearings with liquid lubrication — Lubricant supply arrangements and monitoring 4.2.2 Oil feed and oil return To minimize the possibility of vibrations or thermally induced tensile or compressive stresses occurring in the bearing housing, flexible compensators or connections shall be provided in the oil supply and drain piping systems if applicable. For electrically insulated plain...

ISO 20126 pdf download

ISO 20126 pdf download

ISO 20126 pdf download Dentistry — Manual toothbrushes — General requirements and test methods 1 Scope This document specifies requirements and test methods for the physical properties of manualtoothbrushes in order to promote the safety of these products for their intended use. This document does not specify any requirements and test methods for the physical properties oftoothbrushes for which all...

ISO 20202 pdf download

ISO 20202 pdf download

ISO 20202 pdf download Carbonaceous materials used in the production of aluminium — Cold and tepid ramming pastes — Preparation of baked test pieces and determination of loss on baking 1 Scope This International Standard describes a method of baking green test specimens made by compactingcarbonaceous ramming pastes. lt includes the baking procedure (heating rate and holding time) and thedetermination...