BS ISO 23559 pdf download
BS ISO 23559 pdf download Plastics — Film and sheeting — Guidance on the testing of thermoplastic films
1 Scope
This International Standard identifies specific test procedures to assist producers and users in the selectionand characterization of thermoplastic flms in single- or multi-layer form. lt is intended to serve as a guide forthose films for which there are no existing standards or specifications.
NOTE Because of the range of materials used and the wide variety of processes available to produce various filmconstructions,this document does not address specimen preparation.
lf an International Standard exists for a specific film product, the requirements of that standard shall takeprecedence over this document.
There are many national，regional and industrial standards that address the requirements for specificapplications. Since this International Standard is intended to provide general guidance, it is not within thescope to address these.
The significance of the data and fitness for use shall be determined by the user.
2Normative references
The following referenced documents are indispensable for the application of this document.For datedreferences , only the edition cited applies.For undated references, the latest edition of the referenced document(including any amendments) applies.
IsO 307, Plastics – Polyamides – Determination of viscosity number
ISO 527-3, Plastics —Determination of tensile properties —Part 3: Test conditions for films and sheetsISO 1133-1, Plastics —Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) ofthermoplastics — Part 1: Standard method
ISO 1183-1,Plastics — Methods for determining the density of non-cellular plastics — Part 1: lmmersionmethod,liquid pyknometer method and titration method
ISO 1183-2, Plastics —Methods for determining the density of non-cellular plastics — Part 2: Density gradientcolumn method
ISO1183-3,Plastics —Methods for determining the density of non-cellular plastics — Part 3: Gas pyknometermethod
ISO 2813,Paints and varnishes — Determination of specular gloss of non-metallic paint films at 20, 60°and 85°
ISO 4589-1, Plastics —Determination of burning behaviour by oxygen index—Part 1:Guidance
IS0 4589-2,Plastics —Determination of burning behaviour by oxygen index.— Part 2:Ambient-temperaturetest
ISO 4592,Plastics — Film and sheeting -Determination of length and width
IS0 6383-1, Plastics —Film and sheeting —Determination of tear resistance —Part 1: Trouser tear methodISO 6383-2, Plastics —Film and sheeting —Determination of tear resistance —Part 2: Elmendorf methodISO 7765-1, Plastics film and sheeting —Determination of impact resistance by the free-falling dart method —Part 1: Staircase methods
ISO 7765-2,Plastics film and sheeting—Determination of impact resistance by the free-falling dart method—Part 2: Instrumented puncture test
ISO 8256,Plastics – Determination of tensile-impact strength
ISO 8295, Plastics —Film and sheeting — Determination of the coefficients of frictionISO 8296,Plastics —Film and sheeting —Determination of wetting tension
ISO 9773, Plastics —Determination of burning behaviour of thin flexible vertical specimens in contact with asmall-flame ignition source
ISO 11357-2, Plastics — Differential scanning calorimetry (DsC)— Part 2: Determination of glass transitiontemperature
ISO 11357-3, Plastics —Differential scanning calorimetry (DsC)—Part 3: Determination of temperature andenthalpy of melting and crystallization
ISO 11443,Plastics —Determination of the fluidity of plastics using capillary and slit-die rheometersISO 11501,Plastics —Film and sheeting —Determination of dimensional change on heating
ISO 11502,Plastics — Film and sheeting -Determination of blocking resistance
ISO 13468-1, Plastics —Determination of the total luminous transmittance of transparent materials — Part 1:Single-beam instrument
ISO 13468-2, Plastics —Determination of the total luminous transmittance of transparent materials — Part 2:Double-beam instrument
ISO 14782,Plastics – Determination of haze for transparent materials
ISO 15105-1, Plastics —Film and sheeting —Determination of gas-transmission rate — Part 1: Differential-pressure methods
ISO 15105-2, Plastics —Film and sheeting —Determination of gas-transmission rate—Part 2:Equal-pressuremethod
ISO 15106-1，Plastics — Film and sheeting —Determination of water vapour transmission rate — Part 1:Humidity detection sensor method
ISO 15106-2，Plastics —Film and sheeting —Determination of water vapour transmission rate — Part 2:lnfrared detection sensor method
ISO 15106-3,Plastics — Film and sheeting — Determination of water vapour transmission rate — Part 3:Electrolytic detection sensor method
ISO 15989, Plastics —Film and sheeting —Measurement of water-contact angle of corona-treated filmsIEC 60093,Methods of test for volume resistivity and surface resistivity of solid electrical insulating materialsIEC 60112,Method for the determination of the proof and the comparative tracking indices of solid insulatingmaterials
