API SPEC 19V pdf download
API SPEC 19V pdf download Subsurface Completion Isolation (Barrier) Valves and Related Equipment
1 Scope
This specification provides the requirements for subsurface completion isolation (barrier) valves (SCIV) andrelated equipment as they are defined herein for use in the petroleum and natural gas industries. Included arethe requirements for design, design validation grades, quality levels, manufacturing, functional evaluation, repair,redress, handling, and storage. sClvs provide a means of isolating the formation or creating a blockage in thetubular to facilitate the performance of pre- and/or post-productionvinjection operational activities in the well.
Additional requirements for HPHT products are included in Annex l.
When closed, the SClV provides an obstacle or impediment to flow and/or pressure from above and/or belowand a means of isolating the formation within a conduit.The SCIV is not designed as an emergency or fail-safeflow-controlling safety device.
This specification does not cover installation and maintenance, control systems such as computer systems, andcontrol conduits not integral to the SCIV.Also not included are products covered under ISO 17078, iS0 16070,ISO14310, ISO 10432,ISO 10423, and the following products: downhole chokes, wellhead plugs, sliding
sleeves,casing-mounted flow-control valves, injection valves, well-condition-activated valves, or drill-stem testtools.This specification does not cover the end connections to the well conduit.
2 Normative References
The following referenced documents are indispensable for the application of this document. For dated references,only the edition cited applies.For undated references, the latest edition of the referenced document (includingany amendments) applies.
API.Technical Report 5C3,Calculating Performance Properties of Pipe Used as Casing or Tubing,Annex AAPI Specification 20A, Carbon Steel, Alloy Steel, Stainless Steel, and Nickel Base Alloy Castings for Use in thePetroleun and Natural Gas industry
API. Manual of Petroleum Measurement Standards Chapter 10.4,Determination of Sediment and Water inCrude Oil by the Centrifuge Method (Field Procedure)
API Specification Q1, Specification for Quality Management System Requirements for ManufacturingOrganizations for the Petroleum and Natural Gas lndustry
ANSINACE MR0175-2015/ISO 15156, Petroleum and natural gas industries- Materials for use in HS-containingenvironments in oil and gas production
ASMEaBoiler and Pressure Vessel Code(BPvC),Section ll, Materials Specification—Part D: PropertiesASME.Boiler and Pressure Vessel Code (BPVC),Section VII, Rules for Construction of Pressure Vessels—Division 1,Uw-40: Procedures for Post-weld Heat Treatment
ASME.Boiler and Pressure Vessel Code (BPVC), Section VlII, Rules for Construction of Pressure Vessels一Division 2, Part 5: Design by Analysis
ASME.Boiler and Pressure Vessel Code (BPVC), Section VIIl, Rules for Construction of Pressure Vessels—Division 3: Alternative Rules for Construction of High Pressure Vessels
ASME Boiler and Pressure Vessel Code (BPVC), Section VIII, Division I, UW-51 , Radiographic Examination of Welded Joints
ASME Boiler and Pressure Vessel Code (BPVC), Section VIII, Division 1 , Appendix 8, Methods for Liquid Penetrant Examination (PT)
ASME Boiler and Pressure Vessel Code (BPVC), Section IX, Welding and Brazing Qualifications
ASQ 3 H1 331 , Zero Acceptance Number Sampling Plans
ASTM 4 D395-1 6e1 , Standard Test Methods for Rubber Property—Compression Set
ASTM D41 2-1 6, Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
ASTM D429-1 4, Standard Test Methods for Rubber Property—Adhesion to Rigid Substrates
ASTM D638-1 4, Standard Test Method for Tensile Properties of Plastics
ASTM D790-1 7, Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D1 41 4, Standard Test Methods for Rubber O-Rings
ASTM D1 41 5-06 (201 2), Standard Test Method for Rubber Property—International Hardness
ASTM D1 708-1 3, Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
ASTM D2240-1 5, Standard Test Method for Rubber Property—Durometer Hardness
ASTM D2990-1 7, Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM E21 -09, Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials
ASTM E23-1 6b, Standard Test Methods for Notched Bar Impact Testing of Metallic Materials
ASTM E94/E94M-1 7, Standard Guide for Radiographic Examination Using Industrial Radiographic Film
ASTM E1 1 1 -04 (201 0), Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus
ASTM E1 65, Standard Test Method for Liquid Penetrant Examination
ASTM E709, Standard Guide for Magnetic Particle Testing
ISO 5 3601 -1 , Fluid power systems – O-rings – Part 1: Inside diameters, cross-sections, tolerances and designation codes
ISO 3601 -3, Fluid power systems – O-rings – Part 3: Quality acceptance criteria
ISO 6506 (all parts), Metallic materials — Brinell hardness test
