ISO 20766-24 pdf download

ISO 20766-24 pdf download

ISO 20766-24 pdf download Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 24: Gas tubes
ua uueo
1 Scope
This document specifies general requirements and definitions for the gas tube component of liquefiedpetroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It alsoprovides general design principles and specifies requirements for instructions and marking.
This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuelsin accordance with ISO 9162.It is not applicable to the following:
a) fuel containers;
b) stationary gas engines;
ccontainer mounting hardware;d) electronic fuel management;e)refuelling receptacles.
lt is recognized that miscellaneous components not specifically addressed herein can be examinedfor compliance with the criteria of any applicable part of the ISo 20766 series, including testing to theappropriate functional tests.
All references to pressure in this document are considered gauge pressures unless otherwise specified.This document applies to devices which have a service pressure in the range of 110 kPa (butane rich at20°C) and 840 kPa (propane at 20°C), hereinafter referred to in this document. Other service pressurescan be accommodated by adjusting the pressure by the appropriate factor (ratio).
2Normative references
The following documents are referred to in the text in such a way that some or all of their contentconstitutes requirements of this document. For dated references,only the edition cited applies.Forundated references, the latest edition of the referenced document(including any amendments) applies.ISO 20766-1, Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 1:Generalrequirements and definitions
ISO 20766-2,Road vehicles – Liquefied petroleum gas (LPG) fuel systems components – Part 2:Performance and general test methods
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 20766-1 and the followingapply.
ISO and lEC maintain terminology databases for use in standardization at the following addresses:—ISO Online browsing platform: available at https:/ /www.iso .org/obp
—IEC Electropedia: available at https:f fwww.electropedia ..org/
gas tube
rigid fuel line made by metallic or non-metallic tubing which has been designed not to flex in normaloperation and through which liquified petroleum gas flows
Marking of the component shall provide sufficient information to allow the following to be traced:a) the manufacturer’s or agent’s name, trademark or symbol;
b) the model designation (part number);
c)the working pressure or-working pressure and temperature range;d) the serial number or date code;
e the direction of flow (when necessary for correct installation).The following additional markings are recommended:
– the type of fuel;
– the electrical ratings (if applicable);
— the symbol of the certification agency;
the type approval number;
-a reference to this document.
NOTE This information can be provided by a suitable identification code on at leastone part of the componentwhen it consists of more than one part.
In the event that a component cannot accommodate all marking requirements listed in this document,the manufacturer shall include missing marking information with the packaging of the component.
5 Construction assembly
All gas tubes shall comply with the applicable provisions of IS0 20766-1 and IS0 20766-2,and with thetests specified in Clause 6.
The gas tubes shall be made of a corrosion-resistant material such as copper or stainless steel or theyshall be protected with an external corrosion-resistant coating or non-metallic sleeve.
Gas tubes shall be secured such that they are not subjected to vibration or stresses.
At a fixing point, the gas tube shall be fitted with a protective material protecting against vibration ormechanical abrasion and galvanic corrosion.
Gas tubes shall not be located at jacking points.
At passages the gas tubes whether or not fitted with a protective sleeve, shall be fitted with protectivematerial.
The couplings shall be compatible with the gas tube.

The previous

ISO 20766-16 pdf download

The next

ISO 20766-25 pdf download

Related Standards