ISO 17194 pdf download
ISO 17194 pdf download Structural adhesives — Standard database of properties
This document specifies a set of basic properties commonly required for the selection and use ofstructural adhesives in different applications. ISO standard test methods and test conditions arealso reviewed for the measurement of these data to facilitate traceability of recorded values (seeIntroduction).
2Normative references
The following documents are referred to in the text in such a way that some or all of their contentconstitutes requirements of this document. For dated references, only the edition cited applies.Forundated references, the latest edition of the referenced document (including any amendments) applies.ISO 62, Plastics — Determination of water absorption
ISO 527-1,Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2，Plastics —Determination of tensile properties — Part 2:Test conditions for moulding andextrusion plastics
IS0 868, Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shorehardness)
ISO 1183 (all parts), Plastics — Methods for determining the density of non-cellular plasticsIS0 1817,Rubber, vulcanized or thermoplastic —Determination of the effect of liquids
ISO 2555,Plastics —Resins in the liquid state or as emulsions or dispersions —Determination of apparentviscosity using a single cylinder type rotational viscometer method
ISO 2577, Plastics — Thermosetting moulding materials —Determination of shrinkage
ISo 3219 (all parts),Plastics — Polymers/resins in the liquid state or as emulsions or dispersions 一Determination of viscosity using a rotational viscometer with defined shear rate
ISo 11339,Adhesives – T-peel test for flexible-to-flexible bonded assemblies
ISO 4587,Adhesives —Determination of tensile lap-shear strength of rigid-to-rigid bonded assembliesIS0 6721-4,Plastics — Determination of dynamic mechanical properties — Part 4:Tensile vibration 一Non-resonance method
ISO 6721-5,Plastics —Determination of dynamic mechanical properties — Part 5: Flexural vibration —Non-resonance method
ISO 9142,Adhesives — Guide to the selection of standard laboratory ageing conditions for testing bondedjoints
ISO 10364,Adhesives —Determination of pot life (working life) of multi-component adhesives
ISO 11343,Adhesives —Determination of dynamic resistance to cleavage of high-strength adhesive bondsunder impact wedge conditions — Wedge impact method
ISO 11357-2,Plastics—Differential scanning calorimetry (DSC) —Part2: Determination ofglass transitiontemperature and step height
ISO 11359-2,Plastics —Thermomechanical analysis (TMA)—Part 2: Determination of coefficient of linearthermal expansion and glass transition temperature
IS0 15166-1,Adhesives —Methods of preparing bulk specimens — Part 1:Two-part systems
IS0 15166-2,Adhesives — Methods of preparing bulk specimens —Part 2:Elevated-temperature-curingone-part systems
IS0 17212, Structural adhesives —Guidelines for the surface preparation of metals and plastics prior toadhesive bonding
ISO 25217,Adhesives —Determination of the mode 1 adhesive fracture energy of structural adhesive jointsusing double cantilever beam and tapered double cantilever beam specimens
IEC 62631-3-1, Dielectric and resistive properties of solid insulating materials – Part 3-1: Determination ofresistive properties (DC methods) – Volume resistance and volume resistivity -General method
IEC 60243-1，Electrical strength of insulating materials -Test methods — Part 1: Tests at powerfrequencies
3Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:— ISO online browsing platform: available at https://www.iso.org/obp
-IEC Electropedia: available at https:.//www.electropedia.org/
4Principle
A list is presented of properties that are generally useful for the selection and application of structuraladhesives.Recommended test methods and test conditions are given for each property to help in thedetermination of values and to promote the presentation of traceable and comparable data.
5 Test specimens
Where possible,use the test specimens recommended in the test method standards employed tomeasure the properties given in Tables 1, 2 and 3.If alternative test methods are used, the test methodreference shall be recorded with the results. The preparation of test specimens shall be as specified inISO 17212 for joint specimens and IS0 15166-1 or iSo 15166-2 for bulk specimens. Since the propertiesof adhesives generally depend on the concentration of absorbed water,specimens shall be stored dry orin an atmosphere of (50 主 10) %RH at(23 ±2) °Cprior to testing, for a sufficient time to reach zero orequilibrium water content as indicated by no significant further changes in the mass of the specimenwith storage time.
