Jul,05

IEC 63171-2 pdf – Connectors for electrical and electronic equipment – Part 2: Detail specification for 2-way, shielded or unshielded, free and fixed connectors: mechanical mating information, pin assignment and additional requirements for type 2

IEC 63171-2 pdf – Connectors for electrical and electronic equipment – Part 2: Detail specification for 2-way, shielded or unshielded, free and fixed connectors: mechanical mating information, pin assignment and additional requirements for type 2

IEC 63171-2 pdf – Connectors for electrical and electronic equipment – Part 2: Detail specification for 2-way, shielded or unshielded, free and fixed connectors: mechanical mating information, pin assignment and additional requirements for type 2
1Scope
This part of lEC 63171 covers 2-way, shielded or unshielded, free and fixed connectors for datatransmission up to 600 MHz, with current-carrying capacity, known as Type 2. It specifies thecommon dimensions, mechanical, electrical and transmission characteristics and environmentalrequirements as well as test specifications respectively.
The form factor of these connectors allows their use for cable sharing with already installedTO’s for structured cabling.
NOTE The overall performance of the transmission channel in such case has to be evaluated.
Intermateable and interoperable versions for circular connector for sealed applications includingthis connector are described in lEC 63171-5.
The shielded and unshielded connectors are interoperable for their internal transmissionperformance and can be exchanged. The shielded version has improved alien crosstalk andcoupling attenuation properties.
2Normative references
The following documents are referred to in the text in such a way that some or all of their contentconstitutes requirements of this document. For dated references, only the edition cited applies.
For undated references,the latest edition of the referenced document(including anyamendments) applies.
IEC 60050-581,International Electrotechnical Vocabulary (IEV) – Part 581: Electromechanicalcomponents for electronic equipment
IEC 60512-1,Connectors for electrical and electronic equipment -Tests and measurements -Part 1: Generic specification
IEC 60512-28-100, Connectors for electrical and electronic equipment – Tests andmeasurements – Part 28-100: Signal integrity tests up to 2 000 MHz -Tests 28a to 28g
IEC 60664-1,Insulation coordination for equipment within low-voltage supply systems – Part 1:Principles, requirements and tests
IEC TR 63040,Guidance on clearances and creepage distances in particular for distancesequal to or less than 2 mm- Test results of research on influencing parameters
IEC 63171,Connectors for electrical and electronic equipment – Shielded or unshielded, freeand fixed connectors for balanced single-pair data transmission with current carrying capacity:
General requirements and tests 1
IEC 63171-5,Connectors for electrical and electronic equipment – Part 5: Detail specification
for 2-way,shielded or unshielded, free and fixed connectors: mechanical mating information,pin assignment and additional requirements for type 52
ISO/IEC 11801-1,Information technology – Generic cabling for customer premises – Part 1:General requirements
3 Terms and definitions
For the purposes of this document,the terms and definitions given in IEC 63171,IEC 60050-581, and lEC 60512-1 apply.
ISO and IEC maintain terminological databases for use in standardization at the followingaddresses:
· IEC Electropedia: available at http://www.electropedia.orgl
. Iso Online browsing platform: available at http://www.iso.orglobp
4Common features and typical connector pair
4.1Mating information
4.1.1General
Dimensions are given in millimetres. Drawings are shown in first angle projection. The shapeof connectors may deviate from those given in Figure 2 to Figure 5, as long as the dimensions
specified are not changed, see also Table 1 and Table 2.
NOTE when using the snap-in version of the free connector, the mating face of the free comnector can also be usedas mating face of a fixed connector and the mating face of the fixed connector can be used as mating face of a freeconnector.

Download
The previous

IEC 63169 pdf - Electrical household and similar cooling and freezing appliances – Food preservation

The next

IEC 63185 pdf - Measurement of the complex permittivity for low-loss dielectric substrates balanced-type circular disk resonator method

Related Standards