Jul,04

IEC 61169-15 pdf – Radio-frequency connectors – Part 15: Sectional specification – RF coaxial connectors with inner diameter of outer conductor 4,13 mm (0,163 in) with threaded coupling – Characteristic impedance 50 Ω (type SMA)

IEC 61169-15 pdf – Radio-frequency connectors – Part 15: Sectional specification – RF coaxial connectors with inner diameter of outer conductor 4,13 mm (0,163 in) with threaded coupling – Characteristic impedance 50 Ω (type SMA)

IEC 61169-15 pdf – Radio-frequency connectors – Part 15: Sectional specification – RF coaxial connectors with inner diameter of outer conductor 4,13 mm (0,163 in) with threaded coupling – Characteristic impedance 50 Ω (type SMA)
1Scope
This part of lEC 61169,which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (Ds) for RF coaxial connectors with inner diameterof outer conductor 4,13 mm (0,163 in) with threaded coupling with a characteristic impedanceof 50 (type SMA).
This document specifies mating face dimensions for high performance connectors – grade 1,dimensional details of standard test connectors – grade 0, gauging information and testsselected from IEC 61169-1, applicable to all detail specifications relating to series SMA RFconnectors.
This document indicates recommended performance characteristics to be considered whenwriting a detail specification and it covers test schedules and inspection requirements forassessment levels M and H.
The SMA types RF coaxial connectors are used with all kinds of RF cables and microstrips inmicrowave transmission systems.The operating frequency is up to 18 GHz.These connectorscan be intermated with 3,5 mm (IEEE 287-2007) and 2,92 mm (IEC 61169-35) connectors.
NOTE Metric dimensions are original dimensions. All undimensioned pictorial configurations are for referencepurpose only.
2Normative references
The following documents are referred to in the text in such a way that some or all of theircontent constitutes requirements of this document. For dated references,only the editioncited applies.For undated references, the latest edition of the referenced document(inciuding
any amendments) applies.
IEC 61169-1:2013, Radio frequency connectors – Part 1: Generic specification – Generalrequirements and measuring methods
IEC 62153-4-7:2015, Metallic communication cable test methods – Part 4-7: Electromagneticcompatibility(EMC) – Test method for measuring of transfer impedance Z- and screeningattenuation af or coupling attenuation ac of connectors and assemblies up to and above3 GHz- Triaxial tube in tube method
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
IEC Electropedia: available at http://www.electropedia.org/
ISO Online browsing platform: available at http://www.iso.org/obp
4 Mating face and gauge information
4.1 Dimensions – High performance connectors – Grade 1
4.1.1 Connector with pin centre contact
The mating face of connector with pin centre contact is shown in Figure 1 and its dimensions are shown in Table 1.
NOTE 1 Mechanical and electrical reference plane.
NOTE 2 Coupling nut in forward position.
NOTE 3 Hex 7,85/8,00 mm (0,309/0,315 in) width across flats, 3,18 mm (0,125 in) min flat length. It can extend throughout the full length of the coupling nut. Other structures are also acceptable.
NOTE 4 Sealing ring.
NOTE 5 Spherical or chamfered.

Download
The previous

IEC 61083-1 pdf - Instruments and software used for measurements in high-voltage and high-current tests – Part 1: Requirements for instruments for impulse tests

The next

IEC 61189-5-501 pdf - Test methods for electrical materials, printed boards and other interconnection structures and assemblies – Part 5-501: General test methods for materials and assemblies – Surface insulation resistance (SIR) testing of solder fluxes

Related Standards